Geopolymer concrete-filled pultruded composite beams – Concrete mix design and application

The limited research on the geopolymer concrete mix design for targeting a specific strength is identified an obstacle for their effective design and wide use. In this paper, a mix design procedure has been proposed for fly-ash based geopolymer concrete and its use as infill hybrid composite beam is investigated. Then, the structural performance of geopolymer concrete filled hybrid composite beam is investigated to determine their possible application in civil infrastructure. Firstly, a detailed procedure of mix design for fly-ash based geopolymer concrete is presented. Secondly, three hybrid beams filled with geopolymer concrete were prepared and tested in a four-point bending setup to evaluate their flexural modulus and modulus of rupture. Numerical and analytical evaluation of the behaviour of hybrid beam were performed and results showed a good agreement with the experimental investigation. Thirdly, the suitability of the beam for a composite railway sleeper is evaluated and compared with existing timber and composite sleepers. Finally, the beams’ performance in a ballast railway track is analysed using Strand7 finite element simulation software and the results showed that the new concept of using geopolymer concrete as infill to pultruded composite section satisfied the stiffness and strength requirements for a railway sleeper.     

多组元钛合金电子束冷床炉熔炼挥发规律研究

利用电子束冷床炉(EB炉)一次熔炼制备TC4、Ti6242、TA15钛合金铸锭,采用Langmuir定律对熔炼过程中Al、Sn、Zr、Mo等元素的挥发规律做了简要的数值分析,并与实际挥发规律进行了对比分析。结果表明:EB炉熔炼TC4、Ti6242、TA15钛合金过程中,Al元素在3种合金中的挥发率有所不同,挥发率由大到小顺序为TC4>Ti6242>TA15;Al元素是TC4钛合金中主要的挥发元素;Ti6242钛合金中,Al、Sn元素之间存在联合挥发的问题;TA15钛合金中,Al、Zr元素之间亦存在联合挥发的问题,Al元素带动了Zr元素(难挥发元素)的挥发。     

700 MPa 级高强度大梁钢冲压开裂原因与控制措施

采用 OM 和 SEM 对 700 MPa 级高强度大梁钢冲压开裂原因进行了分析。结果表明，在高强度大梁钢冲压过程中出现的纵梁穿线孔裂纹主要为连冲工艺不当导致；纵梁端部折弯角部裂纹主要是由于原板坯存在内裂纹和大尺寸 TiN 夹杂物，在冲压过程中外表面受到拉应力产生裂纹，裂纹沿横纵向扩展导致。通过将钛质量分数由 0.10% 降至 0.07%，将氮质量分数控制在不大于 0.004% 的范围内，降低大尺寸TiN析出量。化学成分调整后，力学性能满足供货技术条件要求，对钢板进行冲压验证，端部完好，未见折弯裂纹存在，彻底解决了该缺陷。     

高功率光纤激光器光纤器件封装应力影响研究

高功率激光器无源器件制作过程中封装不当引入的应力,会导致信号光光束质量劣化和光纤温升,为了解决此问题,理论分析了光纤形变对信号光模式分布的影响,利用有限元方法建立包层光导致光纤发热模型,实验研究了不同封装方式对光纤发热情况和信号光光束质量的影响。实验表明,应力导致的光纤形变会造成信号光M2值在受力方向上略微变小而其垂直方向上变大,在输出100 W信号光时,施加应力导致的M2值的变化最高为0.39,与仿真结果相符。在光纤温升方面,相比于使用硬质胶水带来的12 ℃温升,使用硅橡胶封装的剥离器将温升控制在5 ℃以内,且其封装应力引入的M2值的变化在0.05以内。     

靶面激光光斑尺寸原位测量的研究

提供了一种简便易行的靶面激光光斑尺寸原位测量的方法。从高斯光束的横向光强分布特性出发,建立了激光烧蚀斑半径与辐照激光能量、光斑尺寸、烧蚀阈值间的关系式,模拟分析发现辐照激光光斑尺寸对烧蚀斑半径随辐照能量变化曲线有较大影响。对于脉宽为2 ms,波长为1064 nm的激光,实验测量了不同能量激光辐照下相纸烧蚀斑半径,并用推导出的关系式拟合测量数据,获得了靶面处光斑尺寸和样品烧蚀阈值。同时,也测量了不同位置处的光斑尺寸和样品烧蚀阈值,对高斯光束束腰位置和样品烧蚀阈值的光斑尺寸效应进行了验证。研究结果表明该技术结果可靠,简单高效。该技术可以为高能激光与固体物质相互作用的基础研究和激光加工等应用领域中实现简单方便地测量靶面光斑尺寸提供帮助。     

High-resolution FIB-TEM-STEM structural characterization of grain boundaries in the high dielectric constant perovskite CaCu3Ti4O12

In this work, the grain boundaries composition of the polycrystalline CaCu₃Ti₄O₁₂ (CCTO) was investigated. A Focused Ion Beam (FIB)/lift-out technique was used to prepare site-specific thin samples of the grain boundaries interface of CCTO ceramics. Scanning transmission electron microscopy (STEM) coupled with energy dispersive X-ray spectrometry (EDXS) and Electron Energy Loss Spectroscopy (EELS) systems were used to characterize the composition and nanostructure of the grain and grain boundaries region. It is known that during conventional sintering, discontinuous grain growth occurs and a Cu-rich phase appears at grain boundaries. This Cu-rich phase may affect the final dielectric properties of CCTO but its structure and chemical composition remained unknown. For the first time, this high-resolution FIB-TEM-STEM study of CCTO interfacial region highlights the composition of the phases segregated at grain boundaries namely CuO, Cu₂O and the metastable phase Cu₃TiO_4.     

45 t门座起重机顶升方案设计

针对国内45 t门座起重机大车行走机构平衡梁裂缝问题。分析平衡梁裂缝产生原因并提出相应的维修方案,并对维修关键技术中的顶升方案设计,采用Ansys软件对其强度进行了有限元分析,同时对维修前后的平衡梁进行分析并对比。将维修方案应用于实际工程,取得了较好效果。该顶升机构修复方案设计符合工程实际,对工程实践具有一定的指导意义。     

电子束诱导沉积钴微米线及其铁磁性

通过电子束诱导沉积的方法制备了钴(Co)微米线,并利用扫描电子显微镜(SEM)、原子力/磁力显微镜(AFM/MFM)以及物性测量系统(PPMS)等手段对Co微米线的沉积尺寸、微结构、铁磁性和电学性质进行了测试和分析。研究结果表明:Co微米线轮廓清晰、均匀性好。在不同的沉积条件下,微米线的实际长度与设定长度基本一致;实际宽度数据呈类梯形分布,半高宽是设定值的2~10倍;实际厚度低于设定厚度的60%。沉积电流对Co微米线的铁磁特性有重要影响。当沉积电流大于0.5 nA时,样品呈现出良好的铁磁特性。另外,电学性能测试结果显示Co微米线呈现绝缘特性。成功制备了室温铁磁绝缘Co微米线,这将有助于深入开展微纳尺度的结构与器件的研究和应用。     

100 MeV质子回旋加速器二期辐照效应管道设计

针对中国原子能科学研究院100 MeV质子回旋加速器上的单粒子效应辐照装置进行了二期管道设计，采用八极磁铁校正法对束流进行了扩束及均匀化，最终在靶上得到了一个30 cm×30 cm、均匀性好于92%的均匀分布的束斑，满足了单粒子效应实验的需求。为降低靶站处的束流能散及中子本底，采用两级降能的方案，在偏转磁铁前放置1个降能片，将能量分为100 MeV和40 MeV两档，并分别针对这两个能量点进行方案设计，束流利用率均在42%以上。公差分析结果表明，四极磁铁对靶上束斑均匀性的影响大于八极磁铁，安装过程中应优先保证四极磁铁的安装公差。     

A fast experimental beam hardening correction method for accurate bone mineral measurements in 3D μCT imaging system

Bone mineral density plays an important role in the determination of bone strength and fracture risks. Consequently, it is very important to obtain accurate bone mineral density measurements. The microcomputerized tomography system provides 3D information about the architectural properties of bone. Quantitative analysis accuracy is decreased by the presence of artefacts in the reconstructed images, mainly due to beam hardening artefacts (such as cupping artefacts). In this paper, we introduced a new beam hardening correction method based on a postreconstruction technique performed with the use of off‐line water and bone linearization curves experimentally calculated aiming to take into account the nonhomogeneity in the scanned animal. In order to evaluate the mass correction rate, calibration line has been carried out to convert the reconstructed linear attenuation coefficient into bone masses. The presented correction method was then applied on a multimaterial cylindrical phantom and on mouse skeleton images. Mass correction rate up to 18% between uncorrected and corrected images were obtained as well as a remarkable improvement of a calculated mouse femur mass has been noticed. Results were also compared to those obtained when using the simple water linearization technique which does not take into account the nonhomogeneity in the object.